- 57
- 1 473 505
MOTHERLODE MOTORS
Приєднався 12 гру 2008
My name is Taylor, I grew up in California's gold country and I love anything to do with cars.
head gasket fix and a day trip to the river
Doing a quick head gasket on the 1930 Ford Model A and then taking it on trip down to Middle Bar Bridge & Pardee Reservoir in Amador & Calaveras Counties.
Переглядів: 4 045
Відео
‘65 Plymouth buried in the woods, is it worth restoring?
Переглядів 4747 місяців тому
I found a 1965 Plymouth Fury III in the woods up in Oregon House, CA and towed it back to my place where we dig into it and see what it's going to take to make it run and drive well enough to handle a road trip.
1930 Ford, expensive radiator & hot weather driving
Переглядів 14 тис.7 місяців тому
In this video we install a Brassworks extreme touring pressurized radiator in my 1930 Ford Model A and see if it can handle the heat.
1930 Ford Camping Trip and First Maintenance
Переглядів 8 тис.8 місяців тому
In this video we do the first maintenance on the car to get to know it a bit better, and take it on a camping trip with some other Model As and Ts in Bridgeport California. Camping at Willow Springs Resort, with a trip down to the Bodie ghost town.
Buying a 1930 Ford
Переглядів 27 тис.8 місяців тому
About a year ago I bought this 1930 Ford, in this video we do the first drive and a walk around. What should I change on the car? Go back to stock? Diesel swap? :) 1930 Ford Model A Four Door Sedan Original paint Original interior Mallory distributor Stromberg downdraft carb Ansen intake manifold 12v conversion
Mopar V8 Poly Head DIY Pushrod Tool
Переглядів 1,5 тис.11 місяців тому
Showing a couple different versions of a pushrod removal/installation tool for Mopar 318 A-block. Removal of the rocker shaft is not necessary. Info on the poly engine... poly318.com/poly-318-engine-history-information/ "Many people throw around the term “poly” as if there was only one type of 1950’s Mopar engine family with polyspherical heads. What we call the “poly 318” is the A-block family...
DIY Teardrop Camper Tour and Weight
Переглядів 18 тис.Рік тому
Sold for $3500 January 2023 See the whole build series here.... ua-cam.com/play/PLobp6KXXWkg7mSskZRgegIzbYhbTNGn_E.html Instagram motherlodemotors
Free MGB sitting for 10 years, will it drive?
Переглядів 10 тис.Рік тому
See all the FREE MGB videos... ua-cam.com/play/PLobp6KXXWkg5R3b-0hTPP-ulbqgEousiq.html Instagram motherlodemotors TikTok www.tiktok.com/@motherlodemotors MGB Wiring Diagrams... www.advanceautowire.com/mgb.pdf
Free MGB sitting for 10 years, will it run?
Переглядів 13 тис.Рік тому
See all the FREE MGB videos... ua-cam.com/play/PLobp6KXXWkg5R3b-0hTPP-ulbqgEousiq.html Instagram motherlodemotors TikTok www.tiktok.com/@motherlodemotors
finish up and first trip for our cheap camper trailer
Переглядів 37 тис.Рік тому
Full Trailer Build Playlist ua-cam.com/play/PLobp6KXXWkg7mSskZRgegIzbYhbTNGn_E.html Materials List docs.google.com/spreadsheets/d/1Xcr89QW0qKp5kmb34itbz7fGaOE6Ya8IrzFSeu3kwjI/edit?usp=sharing Instagram motherlodemotors TikTok www.tiktok.com/@motherlodemotors
FORD Four Banger HILLCLIMB 2022
Переглядів 34 тис.2 роки тому
NorCal F.A.S.T. Spring Hillclimb, Saturday, May 7th, Auburn, CA. Racer fee $50 Spectator fee $10 Open to pre-1935 Ford cars and trucks, stock or modified. Must have Model T, A or B engine to compete. Other pre-1935 4-cylinder engines may compete for time only. www.hotforhotfours.com/
how to make poor mans fiberglass look good
Переглядів 449 тис.2 роки тому
Full Trailer Build Playlist ua-cam.com/play/PLobp6KXXWkg7mSskZRgegIzbYhbTNGn_E.html The L Wood by Lucy ua-cam.com/users/lmw025 Materials List docs.google.com/spreadsheets/d/1Xcr89QW0qKp5kmb34itbz7fGaOE6Ya8IrzFSeu3kwjI/edit?usp=sharing Instagram motherlodemotors
building the galley door for our cheap camper trailer
Переглядів 26 тис.2 роки тому
Full Trailer Build Playlist ua-cam.com/play/PLobp6KXXWkg7mSskZRgegIzbYhbTNGn_E.html Materials List docs.google.com/spreadsheets/d/1Xcr89QW0qKp5kmb34itbz7fGaOE6Ya8IrzFSeu3kwjI/edit?usp=sharing Instagram motherlodemotors
building the roof for our cheap camper trailer
Переглядів 55 тис.2 роки тому
Full Trailer Build Playlist ua-cam.com/play/PLobp6KXXWkg7mSskZRgegIzbYhbTNGn_E.html Materials List docs.google.com/spreadsheets/d/1Xcr89QW0qKp5kmb34itbz7fGaOE6Ya8IrzFSeu3kwjI/edit?usp=sharing Instagram motherlodemotors
building the walls for our cheap camper trailer
Переглядів 25 тис.2 роки тому
building the walls for our cheap camper trailer
building the floor for our cheap camper trailer
Переглядів 18 тис.2 роки тому
building the floor for our cheap camper trailer
modifying a cheap trailer for a camper
Переглядів 14 тис.2 роки тому
modifying a cheap trailer for a camper
will this craigslist mercedes diesel start?
Переглядів 6682 роки тому
will this craigslist mercedes diesel start?
OM616 Throttle Linkage Troubleshooting
Переглядів 1,2 тис.2 роки тому
OM616 Throttle Linkage Troubleshooting
2021 Korbel Hill Climb, Crashes and All
Переглядів 1,6 тис.2 роки тому
2021 Korbel Hill Climb, Crashes and All
building a hitch mount bike rack for a car
Переглядів 13 тис.2 роки тому
building a hitch mount bike rack for a car
2k mile road trip tire failure and other issues
Переглядів 602 роки тому
2k mile road trip tire failure and other issues
Walk around and ride 1985 Goldwing Limited (SOLD $800)
Переглядів 2,4 тис.2 роки тому
Walk around and ride 1985 Goldwing Limited (SOLD $800)
quick stereo install, commuter camry part 2
Переглядів 572 роки тому
quick stereo install, commuter camry part 2
buying the most regular car i could find
Переглядів 1703 роки тому
buying the most regular car i could find
❤❤❤❤ looking very nice 👍👍👍👍👍👍
What wire is for the window to go down?
The Ford fit perfectly in the town where you bought the Pizza... Looked like a very nice, well-kept old town. Where was that?
Sutter Creek CA
Saya suka lihat nya bukan d i kerjain mlaj batnyak omong terus
Take it back to 1930 as much as possible it's much cooler that way
I think you forgot one step an that is you have to bleed master cilinder
You can do it after you install it on the car.
Worry about welding and grinding near the gas tank , otherwise a good repair.Happy motoring
Love how it's all original that's one thing I want is to have one all original with the mohair seats and everything
Paul Shinn channel is a great channel with loads of info on the Model A. Those ar such fun cars I myself is thinking about getting one I would really love a 1932 ford but those things are so expensive and hard to find a good one because many were used as Hot Rods and still are today but the modal A is really cool.
Nice job!
It looks awesome, you did terrific on fiberglass and paint
Wrap those pipes with some aluminum foil, then make a small canal and the oil will flow right into that oil pan
Interesting video. I've been noodling on the idea of buying a Model A. I live in the California desert. While I don't need (or want) to drive on our scorcher days, but to know that a mechanically sound car will be fine on our normally warm days is comforting. Thanks so much. you might invest in a radiator guard to protect that pretty new Brassworks improvement.
Enjoying the Journey with your Fury. It’s a Great watch and learning a lot. That’s what’s it all about with these cherished Mopars. Im looking forward to the future content. Cheers from a fellow Fury II owner.
Does the roughness of the exterior capture dirt more than a smooth, less "porous" (rough) surface?
Since you have a Model A Ford, I believe it would be worth it to join the Model A Ford Club of America.
Running on the Stromberg 97 is an oldschool way of hot rodding in the day. What you have is a 4 banger hot rod. You didn't say whether or not the head is a high compression head or not. My 4 banger uses a Stromberg 81 and I have had great performance with it. It is an original 81 and I have read that it is preferred for the 4 cylinder over the 97. Of course the Zenith carb would be a good choice to go back to.
Use a screw on door knob bumper on the door aligned with the contact point. They make stainless steel and you can paint escutcheon black to match.
Drill new holes on the window for drains and fill the wrong holes with LEXEL. If the functions don’t damage camper trying to “ fix it”!
Same issue with VW valve covers… dry cork and a bale to compress the seal… upgrades include covers with two bolts.😅
Use a micro fiber roller and Rustoleum above the waterline paint as the top coat… results in a very smooth finish.
Great, I watch this every year!
are you fix the problem?
Head gasket ,a lot of seepage !!!!!
👍
You get used to double clutching, I would not change the gearbox, it becomes second nature. Give it time.
Put a flathead in it but not this heavy mercedes diesel boat anchor
You don't sound very enthusiastic for a young man with such a beautiful bike
I have a 2014 Buick Lacrosse and I am having a hard time finding a door wire harness tried eBay. The dealership has discontinued it any suggestions is anything similar to it?
Where do find the connectors
I found some on Amazon. I think your video has been the most helpful I found. My Saturn ion almost all wires are broken on driver's door. Thanks for this video
من فکر میکنم با توجه به ظرافتی که بخرج دادی وزحمتی که کشیدی ۳۵۰۰ دلار قیمت کمی بود امیدوارم ادامه بدی وکار رو تکملتر کنی وبه قیمت بالاتر بفروشی من مجاب شدم که از کار شما کپی کنم وصاحب یک مینی کمپر شوم 🌹👍
Put a diesel in a model A , you should be arrested
Call the cops
So Novi Scored a bit of p..... never mind.
I’m really enjoying watching your videos. I love your 1.5” PVC hose flushing setup. We are working on my dad’s car that’s been sitting for 40 years and going to install the same radiator this weekend. I’m going to use your flushing technique before we do- I think dad will be impressed! Thanks again!
When you put that hub cap back on, I have a 1930 Model A take the wheel off put the hub cap on and on the inside of the wheel bend those tabs over that are sticking through. the hub cap will never fall off again.
Good job replacing that head gasket. Liking your sedan and the 1931 SW Cabriolet Convertible.
I need to replace drivers door harness on my 2006 sienna but can't get to first base. ALL the wires were cut and somebody pulled them out to inside of the car. Only place I see on inside of car to pass the harness is a 1/2 by 1" slot in the car frame. Seems too small to pass connectors through! Help!😅😅
I'm not familiar with that specific vehicle but the harness may need to be installed in the door first and then fished into the car. I'd probably get another harness instead of trying to repair in that situation. You can also find a u-pick junkyard and go see what it's supposed to look like.
Thank you
When shifting down ....clutch pull out of gear release clutch rev up engine clutch again shift to 2nd and release clutch and throttle up
This is brilliant, you come over as an enthusiast like me not an expert which means you are having fun learning all the time about your car , Adrian ( 1935 Morris 10 owner in England)
loved the video reminded me of taking my good lady for a first drive in a 1935 Morris 10 ( in England) Morris is much like the Ford but smaller. Still have the Morris ( and my good lady) 35 years later. Adrian
That's awesome! I've still got the Ford, need to find another lady. 🤷♂
@@MotherlodeMotors Good luck with the Ford and finding a new lady who likes pre war cars ( there are some out there)
great build. impressive. what type of glue did you use for the fibergalss covering? standard type wood glue?
I believe it was titebond 2 or 3. Whatever the waterproof one is.
@@MotherlodeMotors and no issues with water at all like driving in it or did you not have long enough to experience that?
@@doug759 I never had it in the rain.
after 15 mins enough of that whinning glottis choking strangulated voice, ffs learn to speak properly stop choking your glottis and whinning through your nose and breathing irratically.
Funny enough you can use old bedsheets for this instead of canvas Because it's thinner it allows the glue to get better bonding Because my dad did that with his And he also put 2 layers of wire mesh for windows Every few layers Of the bed sheets, also he watered down his glue to let it impregnate the fabric Better. When building the camper in his truck And it's what I plan on doing And I know it's not the poor man's fiberglass anymore After I put a layer of epoxy resin on the outside Just for that extra strength And I plan on doing the same thing for inside on any frame Parts Because I mean in the end it's just really fancy paper mache
Good to see young people getting involved with the old cars. Old cars are a journey and they create a bond. Never sell or you will be sorry.
I would restore the car to original including the carb and distributer and anything else. Work on getting the body which in itself will be a project. Join a Model A club, you probably will come into contact with parts you will probably need.
Bro your car looks like a sports sedan 🎉
You can hitxrod the Model A engine. Lits if parts available for that!
Why would anyone want a diesel engine in a model A?
Opps forgot; Yours is a late '30, get a new speedo cable. Body is the Briggs town sedan. Your headlight need new reflectors, Snyder's has everything you need..
Get a Snyder's Antique Auto catalog, get new hub caps, bend the tabs over with wheels off, then they'll stay on. Never convert a Model A to 12v, this is stupid. I'd convert it back to 6v, also the original Zenith carb, no more fuel pump, gravity feed. Good luck ........